Wire Connectors
Twist-on and crimp connectors for efficient wiring.
Twist-on and crimp connectors for efficient wiring.
BNT Series non-insulated butt and parallel connectors are cut from seamless copper tube and tin-plated. They join two conductors end to end without insulation, then the joint is taped or covered with heat shrink.
View Series
BV Series insulated butt connectors combine a seamless copper tube with a vinyl or nylon sleeve, so a splice can be made without extra insulation. The sleeve is colour coded to the wire range and keeps the joint protected from vibration and moisture.
View Series
PVT Series insulated parallel connectors accept two conductors side by side in a copper tube sleeve and crimp them in a single operation. The tap connection is made without cutting the main conductor, which is the standard method for adding branch circuits to an existing wire run.
View Series
BHT Series heat-shrink butt connectors combine a tin-plated copper splice tube with a dual-wall polyolefin sleeve pre-coated with hot-melt adhesive. After crimping, heating the sleeve seals both wire entries against moisture, making this connector the preferred choice for marine, agricultural and outdoor repair applications.
View Series
WN Series screw-on wire connectors (wire nuts) are twist-on splices with a brass spring insert inside a flame-retardant nylon cap. Spinning the cap onto two or more conductors causes the spring to grip and coil the wires together without stripping or tools. Standard in residential, commercial and light-industrial wiring.
View Series
QS Series quick-splice connectors use an insulation-displacement contact (IDC) that pierces the insulation of both conductors when the cap is squeezed closed, making a branch connection without stripping or tools. The colour-coded PVC housing resists oil, acids and alkalis and is rated for 600 V / 10 A.
View SeriesInsulated terminals specified across automotive, appliance, machinery and power equipment manufacturing.
Panel builders use ring and fork terminals for PLC I/O wiring, contactors and terminal blocks where a secure screw connection is required.
Harness makers specify colour-coded insulated terminals for lighting, sensor and power circuits, where vibration resistance matters.
Washing machines, air conditioners and ovens rely on fully insulated terminals for internal wiring that must stay safe and compact.
Machine builders fit ring, fork and disconnect terminals to motors, sensors and control cabinets operating in demanding environments.
Switchgear and distribution boards use tin-plated copper terminals for stable current transfer and resistance to corrosion.
PHOENIX offers BNT non-insulated butt connectors, BV vinyl and nylon insulated butt connectors, PVT vinyl-insulated parallel connectors, BHT long full-insulated butt connectors, WN screw-on wing connectors with spring insert and QS quick splice connectors.
A butt connector joins two wires end to end in a straight line. The two stripped conductors enter each end of a metal sleeve and are crimped in place, creating a permanent inline splice used in automotive, appliance and building wiring.
BNT connectors are bare metal sleeves that must be insulated separately with tape or sleeving after crimping. BV connectors include a vinyl or nylon insulation barrel that covers the joint, giving built-in insulation and strain relief.
PVT parallel connectors join two wires side by side rather than end to end. They are used to branch or extend a conductor in lighting circuits and appliance harnesses, with a vinyl insulation sleeve over the crimp.
BHT connectors have an extended insulation barrel that covers both the crimp and the wire jacket, providing a sealed, strain-relieved joint. They are suited to outdoor, marine and damp locations where a standard butt connector would be exposed.
WN wing connectors use a spring insert inside a screw-on insulated cap. You strip the wires, push them into the cap and twist the wing shell, which draws the conductors together into a secure spring-locked connection. They are reusable and need no crimping tool.
QS quick splice connectors let you tap into an existing wire without cutting it. The main wire stays intact while a second wire is inserted into the side channel, and a hinged metal clip is pressed down with pliers to pierce the insulation and make contact.
Match the connector to the wire cross-section, usually 22–10 AWG (0.5–6 mm²), and choose the insulation style for the environment. Use insulated or heat shrink types outdoors, and match the color code to the wire range.
Crimp-style butt and parallel connectors are permanent and should not be reused once crimped. WN screw-on wing connectors can be removed and reused if the spring insert is undamaged. QS quick splices are intended for single use.
Crimp connectors need a ratcheting crimp tool with the correct die, while WN wing connectors and QS quick splices only need a screwdriver or pliers. For waterproof joints, add a heat shrink sleeve over the finished connection.
Tell us your wire size and requirements, and we will help you find the right solution.
Request a Quote